Heating & Cooling Services in Barberton, OH

Performed scheduled maintenance on aging furnace (10+ years). Inspected control board and wiring connections, noting some corrosion on metal components. Examined wall mounting and surrounding structure for proper ventilation and support integrity.

Diagnosed intermittent cold air issue on 8-year-old furnace. Performed combustion analysis with Bacharach analyzer, confirming system is operating at 95.2% efficiency with acceptable CO levels (34 ppm) and proper stack temperature (105°F). All parameters within manufacturer specifications.

Performed comprehensive furnace clean and check service. Conducted combustion analysis testing using Bacharach analyzer, which verified system efficiency at 82.3% with CO levels at 16ppm, O₂ at 9.8%, CO₂ at 6.3%, and stack temperature of 294°F. Explained preventative maintenance benefits to customer.

Conducted site assessment of existing HVAC system in basement utility area, including evaluation of aging Belcary furnace unit and associated ductwork. Documented current installation conditions and prepared replacement estimate for complete system upgrade to improve efficiency and reliability.

Responded to service call for commercial furnace repeatedly tripping breaker. Inspected electrical components and wiring, identifying loose connections in the control board assembly. Secured all electrical connections and verified proper operation of unit with no further breaker trips during extended testing cycle.

Successfully installed a new tankless water heater system with proper venting, including dual white exhaust pipes and ventilation ductwork. Completed copper pipe connections for water supply and return lines, securing all piping with appropriate mounting brackets and ensuring proper joint connections throughout the system.

Completed full system replacement in residential basement, installing new Lennox furnace unit with properly connected ventilation system including metal ductwork, return plenum, and integrated humidifier. All components were secured to manufacturer specifications with proper clearances maintained for optimal system performance and efficiency.

Successfully installed and configured AprilAire humidifier system per service request. Connected unit to existing HVAC controls, ensuring proper integration with the digital programmable thermostat. Verified system functionality with humidity control dial calibrated to optimal settings for the space.

Responded to service call for leaking Kenmore water heater. Upon inspection, confirmed tank failure requiring complete replacement. Installed new water heater, connected to existing copper and PVC plumbing system, and verified proper operation before leaving premises.

Responded to service call for furnace exhibiting short-cycling behavior (igniting for 5-10 seconds before shutting off repeatedly). Performed combustion analysis using Testo 310 gas analyzer, which showed normal oxygen levels (8.5%) and minimal carbon monoxide (4 ppm), confirming proper combustion despite cycling issues.

Successfully installed a new commercial tanked water heater in utility room with proper copper pipe connections and fittings, including pressure relief valve. Completed installation of metal flue pipe for proper venting, and ensured all connections were secure with no leaks upon final testing.

Diagnosed furnace with short-cycling issue where unit would ignite but shut down after approximately 15 seconds. Performed combustion analysis with Testo 310 analyzer on Rheem unit, measuring CO levels at 14 ppm and 10 ppm, and combustion efficiency at 55%. Testing confirmed proper operation after service.

Responded to service call for furnace running continuously without producing heat. Performed combustion analysis on natural gas system, verifying proper O2 (7.59%), CO (0 ppm), and CO2 (7.46%) levels with 88.5% efficiency. Inspected and measured component dimensions to ensure proper fit and function, resolving the heating issue.

Successfully completed installation of a new Lennox furnace in basement utility area. Installed complete metal ductwork system with proper ventilation connections, including vertical and horizontal galvanized components. System was fully tested and verified to be operating according to manufacturer specifications.

Responded to service call for non-functioning unit heater. Diagnosed issue with thermostat displaying -3 degrees, indicating possible temperature sensor malfunction or wiring issue. Repaired thermostat connections and verified proper system operation before departure.

Responded to service call for non-functioning furnace from the 1980s with pilot light issues. Upon inspection of the olive green basement unit, diagnosed faulty pilot assembly. Replaced pilot assembly, cleaned burners, and verified proper ignition sequence. System now operating within normal parameters with strong, consistent flame pattern.

Responded to service call for 15+ year old humidifier that wasn't operating properly. Upon inspection of the mechanical room and associated ductwork, diagnosed system issues and provided customer with recommendations for repair or replacement options based on equipment age and condition.

Responded to service call for furnace not working and blowing cold air. Performed combustion analysis on natural gas furnace using Bacharach analyzer which showed acceptable readings (O₂: 6.6%, CO: 21ppm, CO₂: 8.1%) with system operating at 83.0% efficiency. Restored proper heating function to ensure customer comfort ahead of incoming storm.

Performed scheduled commercial heating maintenance visit. Inspected refrigeration unit showing signs of frost buildup and condensation on interior shelving. Documented equipment condition with photos for service record.