Heating & Air Conditioning Services in Massillon, OH

Completed scheduled cooling maintenance on 8-year-old residential air conditioning system. Performed comprehensive inspection of furnace, air handler, and ductwork assembly, verified proper operation of all components, checked refrigerant levels, cleaned condenser coils, inspected electrical connections, and confirmed adequate airflow through the system. All equipment found to be functioning within manufacturer specifications with no deficiencies noted.

Completed spring maintenance on residential cooling system. Inspected and serviced HVAC equipment, including verification of April Aire humidifier component (Part No. 80 replacement canister) installation and proper operation. Confirmed all supply and return air vents functioning correctly throughout living spaces, with system operating within normal parameters.

Completed full installation of new Lennox furnace system with integrated air quality components in residential basement mechanical room. Installed air scrubber and air cleaner units to enhance indoor air quality and filtration capabilities. Connected all necessary ductwork, including metallic supply ducts and flexible return connections, ensuring proper airflow distribution throughout the system. Mounted digital thermostat control on wall for system operation and temperature management. Completed all electrical connections to dedicated circuit box, verified proper voltage and amp draw. Installed humidifier unit with water supply line connections for whole-home humidity control. Secured all refrigerant lines, condensate drainage, and gas supply connections per manufacturer specifications and local code requirements. Tested all safety controls including limit switches, pressure switches, and flame sensors to confirm proper operation. Verified furnace ignition sequence, blower motor opera

# HVAC Install - Complete System Completed full retrofit installation of two complete HVAC systems including furnaces and air conditioning units. Installed outdoor condensing units on composite pads with proper gravel base for drainage and stability. Ran new refrigerant linesets with appropriate insulation from indoor air handlers to outdoor units. Mounted indoor air handler equipment in mechanical closet with proper clearances for service access. Installed new PVC condensate drain lines with proper pitch and termination points. Ran electrical disconnects and wiring to outdoor units per code requirements. Connected flexible metallic conduit for electrical connections to indoor equipment. Mounted control boards and wiring for both systems in mechanical space. Ensured all refrigerant lines properly sealed and insulated where penetrating building envelope. Positioned outdoor units with adequate clearance from landscaping and structures for airflow and future maintenance access. Verifie

Conducted furnace replacement estimates for duplex property, evaluating existing Airtemp heating units in both utility spaces. Assessed current system conditions, ductwork configurations, and venting arrangements to provide comprehensive replacement recommendations, with additional evaluation for potential air conditioning system upgrades.

Responded to emergency no-heat call at commercial bingo hall with indoor temperature at 55°F. Upon arrival, inspected commercial furnace system and associated ductwork, identified and resolved heating system malfunction, and restored full operational capacity to ensure facility would be adequately heated for scheduled evening event.

Successfully installed a Daikin 7.5-ton rooftop package unit for a commercial new construction project. The unit was positioned on a concrete pad at ground level adjacent to the building, with metallic ductwork connected vertically to the structure. Electrical disconnect box was wired and equipped with TR60R 600V AC fuses, ensuring proper overcurrent protection and safe disconnect capability for the equipment.

Installed customer-supplied whole house water filtration system with complete rework of existing copper water lines. The installation included mounting a black cylindrical filter housing to the basement wall, integrating a red-handled shutoff valve and pressure regulation device, and reconfiguring copper piping with brass fittings to accommodate the new filtration system while maintaining proper water flow throughout the residence.

Responded to no heat call on newly installed furnace in pavilion. Upon arrival, found thermostat displaying 53°F and not calling for heat. Inspected furnace control board and electrical connections, verified all wiring terminations at White-Rodgers control module and terminal strips were secure. Cycled thermostat to initiate heat call, confirmed proper communication between thermostat and furnace control board. System now operating normally and providing heat to space.

Responded to water leak at whole house water filter system in 1971-built residence. Upon inspection, identified small leak at filter housing connection point. Repaired leak by tightening housing assembly and replacing O-ring seal to restore proper water-tight integrity. System tested and verified no further leakage present. Filter assembly located in basement utility area with PVC supply lines running along foundation wall.

Responded to no heat call for back pavilion area with blank thermostat display. Upon inspection, diagnosed failed pressure switch on rooftop HVAC unit serving the affected zone. Replaced defective pressure switch, restored power to thermostat, and verified system operation with successful heating cycle.

Completed fall maintenance service on commercial HVAC system. Inspected and replaced ignition sensor component which showed signs of wear. System was tested after component replacement and is now operating within normal parameters.

Completed final commissioning of HVAC system in new construction project. Installed and verified proper functionality of ceiling register with horizontal slats for optimal airflow distribution. System is operating according to specifications with all components properly secured and balanced.

Performed fall maintenance on heating system. Conducted combustion analysis using Bacharach gas analyzer, which verified optimal system performance with 91.0% efficiency, appropriate oxygen (9.8%) and carbon dioxide (6.3%) levels, and safe carbon monoxide readings (7 ppm) at normal stack temperature (111°F).

Performed routine maintenance on residential heating system. Conducted combustion analysis with Bacharach Fyrite INTECH analyzer, confirming optimal operation with O₂ at 8.6%, CO at 16 ppm, CO₂ at 6.9%, and efficiency rating of 90.6% for natural gas combustion.

Responded to no-heat call where furnace burner was operational but circulation pump failed to activate. Performed combustion analysis with Sauermann analyzer, confirming proper gas combustion with 80.2% efficiency, 11.46% O2, 0 ppm CO, and 5.33% CO2. Restored proper operation by repairing circulation pump issues.

Performed furnace maintenance service as requested. Conducted combustion analysis using Testo 310 analyzer, verifying CO levels (5-9 ppm) and oxygen levels (8.5%) within acceptable parameters. Diagnosed and resolved issue preventing furnace ignition, returning system to proper operation.

Performed scheduled commercial heating maintenance and identified significant corrosion on system piping. Removed and inspected temperature probe/sensor, which showed signs of wear. Documented condition with photos for future reference and customer records.

Successfully installed a new Lennox furnace system with proper PVC venting in the utility room. Connected and calibrated the Honeywell digital thermostat to ensure accurate temperature control. All components were properly secured and tested for optimal performance.

Performed scheduled residential heating maintenance service. Conducted combustion analysis using Bacharach gas analyzer, confirming system is operating at 94.9% efficiency with acceptable CO levels at 28ppm and stack temperature of 105°F. All parameters within normal operating range.