Akron, OH 44313 has a mix of homes and businesses that makes HVAC and plumbing work different from one part of the ZIP code to another. Around Fairlawn Heights and the West Akron residential borders, we work in established mid-century homes, upscale traditional properties, and split-levels with standard basements and conventional ductwork. Closer to Montrose, newer residential development sits alongside one of the area's busiest retail and dining corridors.
That variety affects how heating, cooling, plumbing, and indoor air quality systems perform. Lakes Heating & Air Conditioning works throughout 44313 helping homeowners solve comfort problems based on the house itself, whether that means aging ductwork in an established property or newer high-efficiency equipment that needs proper airflow to perform well. Call (330) 536-1276 or contact Lakes Heating & Air Conditioning online to schedule service in Akron.
HVAC Service For The Homes Around Fairlawn Heights And West Akron
Much of the housing in 44313 dates to the middle and later decades of the twentieth century. Standard basements, conventional duct systems, split-level floor plans, and larger traditional homes are common, while newer residential development adds a different generation of HVAC equipment to the area.
That mix matters when we troubleshoot comfort problems. A split-level near the West Akron side of the ZIP code may develop noticeable temperature differences between floors, while a larger Fairlawn Heights property can have longer duct runs that make it harder to keep distant rooms consistent. We look at the equipment, ductwork, controls, and layout together instead of assuming every comfort issue starts at the furnace or air conditioner.
Heating Repair And Furnace Service In Akron, OH 44313
Cold, snowy Northeast Ohio winters put steady demand on heating equipment throughout 44313. Established homes around Fairlawn Heights may have furnaces that have already been replaced more than once, while newer properties are more likely to use high-efficiency or multi-stage equipment.
Those newer systems still depend on the rest of the house. If conventional ductwork from an earlier installation cannot move enough air, a high-efficiency furnace may still leave certain rooms uncomfortable during longer winter run cycles.
Our heating services include:
- Emergency heating
- Heating repair
- Heating installation
- Heating maintenance
- Furnaces
- Boilers
- Heat pumps
- Geothermal services
- Space heating
- Snowmelt systems
- HVAC services
- New construction HVAC
- Commercial heating
When a split-level near West Akron develops a colder section of the house, we check blower performance, filters, thermostat operation, duct restrictions, and airflow before recommending major equipment changes. The goal is to determine whether the furnace is struggling or whether the heat simply is not getting where it needs to go.
AC Repair And Cooling Service Near Sand Run And Fairlawn Heights
Warm, humid summers are part of living in Northeast Ohio, and homes around Sand Run Metro Park and Fairlawn Heights can feel the effects quickly. Larger traditional homes and multi-level layouts may cool well in one area while upstairs bedrooms or distant rooms stay warmer.
Humidity can also be an issue even when the thermostat reaches its setting. In a home with older conventional ductwork, weak return airflow or previous modifications can affect both temperature control and how well the system removes moisture.
Lakes provides:
- Emergency AC services
- AC repair
- AC installation
- AC maintenance
- Ductless air conditioning
- Packaged units
- HVAC services
- New construction HVAC
- Commercial AC
High-efficiency AC upgrades are common for the suburban housing in 44313, but we do not look at efficiency ratings alone. We check system operation, airflow, duct condition, and how the house responds during longer cooling cycles so new equipment can perform the way it was designed to.
Plumbing Service For Established Akron 44313 Homes
Standard basements are common throughout the mid-to-late twentieth-century housing around this part of Akron. That usually puts the water heater, main plumbing lines, drain connections, furnace, and other mechanical equipment in one central area.
In an established Fairlawn Heights or West Akron home, that basement may show several generations of updates. Newer plumbing can sit beside older sections of the system, while bathroom or kitchen remodeling may have changed some lines without replacing everything else. Understanding those changes helps us trace where a plumbing problem actually starts.
Our plumbing services include:
- Plumbing installation
- Plumbing repair
- Water heaters
- Drain cleaning
- Bathroom remodel plumbing
- Faucet installation and repair
- Leak detection and repair
- Gas line installation
- Garbage disposals
- Toilets
- Sinks
- Sump pumps
Recurring slow drains, inconsistent water pressure, leaking fixtures, or a water heater that no longer keeps up with daily use can all signal a developing problem. We would rather identify what is happening early than wait until a smaller issue disrupts the whole house.
Indoor Air Quality For Humid Summers And Dry Winters
The wooded surroundings near Sand Run Metro Park give this part of Akron a different feel from the Montrose commercial corridor, but every home still deals with the same seasonal swings. Summer brings warm, humid air, while long winter heating cycles can leave indoor conditions noticeably dry.
That makes indoor air quality especially relevant in homes that have received updated windows, efficiency improvements, or HVAC replacements over the years. The house may hold air differently than it did when its original conventional duct system was installed.
We install and service:
- Air cleaners
- Air scrubbers
- Air purifiers
- Humidifiers
- Dehumidifiers
- Thermostats
- Carbon monoxide detection
- Air ducts and ductwork
Whole-home air scrubbers and humidifiers are a good fit for the type of modern suburban family living common in 44313. We also look at ductwork and airflow because filtration and humidity equipment work best when conditioned air can circulate properly throughout the house.
Commercial HVAC Service Around The Montrose Corridor
Montrose gives 44313 a commercial side that looks very different from the residential streets around Fairlawn Heights. Retail stores, dining destinations, and other businesses create a busy suburban-urban mix where heating and cooling equipment can operate for long hours with changing occupancy throughout the day.
Lakes provides commercial heating, commercial AC, packaged-unit service, and new construction HVAC for properties with those heavier demands. We look at how the space is used, where comfort problems occur, and how the equipment performs during business hours before recommending repairs or replacement.
That local mix becomes especially noticeable during major community activity, from the annual Fairlawn Apple Festival to larger regional gatherings like the Summit County Fair. Busy commercial and residential areas both depend on dependable heating and cooling when more people are moving through the area.
Schedule HVAC And Plumbing Service In Akron, OH 44313
A service call near Sand Run can look very different from one closer to Montrose or Fairlawn Heights. One home may have decades-old ductwork feeding a newer furnace, while another has modern equipment installed in a larger suburban layout with longer runs and multiple comfort zones. Those differences are exactly why we do not treat every 44313 property the same way.
Lakes Heating & Air Conditioning provides heating, air conditioning, plumbing, commercial HVAC, and indoor air quality service throughout Akron, OH 44313. Call (330) 536-1276 or contact us online today to schedule service for your home or business.
Recent Jobs and Reviews in Akron, OH
Akron, OH at a glance
Lakes Heating, Air Conditioning & Plumbing INC has completed 20 jobs in Akron, OH in November 2026.
The most recent job was on November 12, 2026.
Lakes Heating, Air Conditioning & Plumbing INC has completed 875 jobs in Akron, OH in the last 12 months.
Job Locations and Reviews
Completed a full HVAC system installation, including a new outdoor condenser unit mounted on a wall bracket with a code-compliant electrical disconnect and conduit run. Insulated refrigerant lines were routed through the exterior wall, and a condensate drain line was installed and terminated away from the structure. Refrigerant line sets and electrical connections were secured and sealed, with the system commissioned and operating within specifications.
Performed seasonal heating maintenance on a 17-year-old natural gas furnace, including inspection of the combustion system and operational check of the unit. Combustion analysis was recorded at 9.5% Oâ‚‚, 6.4% COâ‚‚, 6 ppm CO, 329°F stack temperature, and 81.2% efficiency, with CO within safe limits. The furnace was left operating normally at completion.
Performed seasonal heating system maintenance and combustion analysis on the natural gas furnace. Analyzer readings were within normal operating range: Oâ‚‚ 7.8%, CO 15 ppm, COâ‚‚ 7.4%, and stack temperature 91°F, confirming safe and proper combustion.
Performed an on-site estimate for installing a gas line to serve a fireplace. Inspected the masonry firebox, noting existing electrical cabling and soot buildup inside the enclosure, and evaluated the adjacent mechanical space, where existing black iron piping and a duct cabinet were identified as potential routing and tie-in points. Documented site conditions with photos to determine pipe routing, termination location, and material requirements for the new gas line.
Performed annual heating maintenance on a gas furnace, inspecting the blower assembly, burners, heat exchanger, gas valve, wiring, and control board with the cabinet panels removed. Burners ignited and operated with a stable blue flame, and the unit cycled properly through heating operation. Noted light rust on the burner components and dust and dirt buildup inside the cabinet, and checked the air filter condition.
Performed an on-site evaluation for replacement of an existing upflow gas furnace in a basement utility space. Removed the front access panel and inspected the inducer motor, control board, wiring, and flue connection, noting heavy dust accumulation, surface wear, and rust on the adjacent gas piping. Documented the unit's condition, flue configuration, and attached ductwork to determine replacement scope and compatibility.
Reconnected the sink to the countertop and re-secured the loose drain plumbing beneath the basin. Inspected the under-sink assembly, including the P-trap slip-joint fittings, garbage disposal connection, and flexible drain hose, and confirmed all connections were tight and properly aligned. Noted existing water staining on the cabinet back wall from prior moisture exposure.
Performed an on-site evaluation and replacement estimate for a furnace and air conditioning retrofit. Inspected the existing outdoor condenser unit, which shows corrosion on the fan guard and hub, along with its disconnect and electrical whip, and assessed the gas-fired upright furnace with its burner assembly, blower motor, control board, flue connection, supply plenum, and gas supply piping for replacement scope. No frost, rust, or visible damage was found on the furnace cabinet, and the condenser pad and surrounding area were noted for clearing of debris prior to installation.
Responded to a no-heat call on a 14-year-old gas furnace that would not start. Diagnosed and corrected the cause of the failure, restored the unit to operation, and verified safe performance with a combustion analyzer, which showed 7.0% Oâ‚‚ and 6 ppm CO. Heat is now functioning properly.
Performed fall heating maintenance on two natural gas furnaces, including combustion analysis with a calibrated flue gas analyzer to verify safe, efficient operation. Readings on both units were within normal parameters, with CO at 12–13 ppm, O2 at 6.9–7.3%, and CO2 at 7.6–7.8%, confirming proper combustion and venting.
Performed an on-site evaluation for a possible ductless mini split installation and system zoning in the basement mechanical and storage area. Inspected the existing insulated rectangular sheet-metal trunk ductwork, access panel, and adjacent copper and black piping, finding no visible corrosion, frost, or damage, and documented the available wall and ceiling space, clearances, and equipment locations for indoor head placement and line set routing. Findings were recorded with photos to support equipment sizing and zoning recommendations.
Responded to a no-heat call on a natural gas furnace and diagnosed a failed hot surface ignitor, which was preventing ignition. After restoring heat operation, performed a combustion analysis showing O2 at 5.4%, CO at 48 ppm, CO2 at 8.7%, and 98.4% efficiency, confirming the unit is operating within acceptable parameters.
Removed two existing 40-gallon water heaters and installed a new 50-gallon Bradford White gas water heater, reworking the copper water supply lines with soldered joints, a brass mixing valve, and isolation ball valves. Installed a thermal expansion tank, reconnected the gas supply with a shutoff valve, and reconfigured the flue with a draft hood and galvanized vent connector routed to the existing chimney. System inspected with no visible leaks or defects.
Performed scheduled maintenance on a ceiling-suspended Reznor unit heater serving a large indoor athletic facility, inspecting the cabinet, louvered discharge grille, electrical conduit, and flue venting; no frost, rust, or damage was observed on the unit or its mounting. Inspection also identified a visible crack in an insulated pipe or tubular component, along with minor surface rust on an adjacent pipe, which should be evaluated for repair or replacement to prevent further deterioration.
Performed a combustion analysis on the Knight modulating condensing boiler using a Bacharach Fyrite InTech analyzer, recording O2 at 6.9%, CO at 25 ppm, CO2 at 7.9%, and combustion efficiency of 90.6% on natural gas. Verified boiler operation at 99% modulation with a 10°F delta T, 125°F flue temperature, 12.8 µA flame signal, and approximately 6,996 RPM fan speed, confirming the unit is operating within normal parameters. Inspected and tested the furnace for proper operation as part of the system check.
Performed annual heating maintenance on a 15-year-old gas furnace, including a full system inspection and operational check. Removed the heavily soiled, dust-laden air filter and installed a clean replacement to restore proper airflow and protect the blower and heat exchanger.
Responded to a no-heat call and performed a diagnostic inspection of the furnace system, including the Nest thermostat and unit controls, with the filter condition noted as unknown and in need of inspection and replacement. During the service, heavy corrosion was documented at the bottom of the electrical panel enclosure, which presents a safety and reliability concern for the electrical supply and should be evaluated by a licensed electrician.
Removed the existing furnace and installed a new gas-fired upflow furnace, connecting it to the existing galvanized supply plenum and ductwork with foil-taped seams. Installed PVC combustion air intake and exhaust venting with a condensate drain line, reconnected the gas supply with a flexible line and shutoff valve, and completed the electrical connections. Sealed pipe penetrations and labeled the unit, with all connections secure and no visible leaks or damage.
Responded to a no-heat call on a gas-fired system and performed a combustion analysis, which returned O2 8.9%, CO2 6.8%, CO 19 ppm, and 80.6% efficiency on natural gas. Inspected the hydronic components and noted heavy corrosion and mineral deposits on the cast iron air separator, along with verdigris at copper pipe fittings and rust staining on the adjacent wall, indicating possible past or active leakage. Recommend further evaluation of the corroded hydronic components and monitoring for leaks.
Installed a new 40-gallon Bradford White natural gas tank water heater with a power anode rod to extend tank life and reduce corrosion. Connected the gas supply, venting, and copper water lines, and installed an expansion tank to manage thermal expansion within the system.
