Heating, Cooling & Air Quality Services in Akron, OH

Responded to a leaking tanked gas water heater complaint and inspected the Rheem Performance unit, including the supply connections, T&P discharge piping, vent connector, and burner compartment. Noted rust residue and debris at the base of the unit and documented the condition with photos for further evaluation and recommendations.

Performed a scheduled heating maintenance visit and conducted a flue gas combustion analysis on the natural gas-fired appliance using a Testo digital analyzer. Readings recorded 7.2% O2, 46.7% excess air, 34 ppm CO, and 52 ppm air-free CO, confirming combustion performance and flue gas safety levels were within acceptable operating range. Equipment age was undetermined, and the customer was advised that the maintenance plan is due for renewal.

Retrofitted the existing gas furnace with a new AC system, installing the evaporator coil on the supply plenum and connecting it to the condensing unit with refrigerant lines. Sealed and secured the supply duct transitions and plenum connections, and verified gas line connections, venting, and condensate drainage. Commissioned the complete system, confirming proper airflow, refrigerant charge, and heating and cooling operation.

Installed a new gas-fired boiler with a stainless steel vent connection to the ceiling, along with new soldered copper supply and return piping, isolation ball valves, a pressure gauge, and a circulator pump with digital display. Mounted an expansion tank and added drain fittings and flexible conduit for electrical connections. The completed installation is clean, properly supported, and free of visible leaks, rust, or damage.

Responded to a no-heat call on a 2-year-old gas furnace and performed a full system inspection, including the control board, wiring harness, gas valve, and burner assembly. Noted soot and carbon residue on the burner compartment and gas piping, and verified the control board status indicator for diagnostic fault codes. Cleaned the burner area and checked all connections to restore proper furnace operation.

Replaced flexible ductwork with rigid hard pipe on all return air runs in the framed ceiling and wall cavities to improve airflow performance and system durability. Secured and sealed all transitions and connections to boots and collars to ensure proper return air delivery under the new construction warranty.

Performed an on-site assessment for a commercial multi-zone mini split system installation consisting of three outdoor units and nine indoor units. Inspected the existing rooftop mounting area and Mitsubishi Electric condensing units, and evaluated the available electrical service, including a GE A Series panelboard with labeled circuits for the 2nd floor commons and rooftop AC unit, to determine breaker capacity and circuit requirements. Documented existing equipment placement, support blocking, and refrigerant line routing conditions to support system sizing and installation planning.

Responded to a no-heat call on a 6-year-old furnace that failed to start when the thermostat called for heat. Performed diagnostics on the system, including inspection of the integrated furnace control board and low-voltage thermostat wiring connections, and documented the unit's model and serial numbers along with the replacement part information. The control board showed no visible burns, corrosion, or physical damage.

Performed annual heating maintenance on a 3-year-old natural gas furnace, including combustion analysis with a calibrated flue gas analyzer. Readings showed O2 at 8.43%, CO2 at 7.00%, and CO at 37 ppm, indicating safe combustion levels and proper burner operation. System was left operating normally.

Performed annual gas furnace maintenance, including inspection of the inducer/collector assembly, gas piping and valve, wiring harness, PVC vent and condensate drain connections, and interior cabinet components, with no breakage, rust, or leaks observed. Conducted a combustion analysis on natural gas, with flue gas readings of 8.1% O2, 4 ppm CO, and 7 ppm air-free CO confirming safe, efficient combustion within normal operating parameters.

Performed fall heating maintenance on the natural gas furnace, including a flue gas combustion analysis showing 6.9% O2, 43.8% excess air, and 11 ppm CO (16 ppm air-free), all within acceptable operating limits. Inspected and serviced the return air filter, which showed moderate dust loading, to maintain proper airflow and system efficiency. Unit operation verified with no visible rust, frost, or damage observed.

Responded to a no-heat call on a Comfort-Aire gas furnace reported to have a buzzing noise and failure to cycle, with a suspected blower motor or control board fault. Inspected the inducer assembly, pressure switch, gas valve, and burner compartment, then restored operation with stable burner flame established. Verified performance with a combustion analysis on natural gas, recording 5.6% O2, 32.5% excess air, 27 ppm CO, and 37 ppm air-free CO, all within acceptable limits.

Responded to a no-cool call on a 16-year-old gas furnace and performed a combustion analysis on the flue gas using a Testo 327-1 analyzer. Readings showed 6.0% O2, 35.8% excess air, 7 ppm CO, and 10 ppm air-free CO, all within acceptable operating limits for natural gas combustion.

Performed fall heating maintenance on a natural gas furnace, including a combustion analysis to verify safe and efficient operation. Flue gas readings were within acceptable range, with O2 at 8.2%, CO2 at 7.1%, CO at 9 ppm, and steady-state efficiency of 88.1%. System operating normally at completion of service.

Performed scheduled heating maintenance on a gas-fired furnace, including inspection of the unit and verification of proper operation. Conducted a combustion analysis using a digital analyzer on natural gas, recording O2 at 7.32%, CO at 7 ppm, and CO2 at 7.62%, with CO levels well within safe limits and indicating clean, stable combustion. No deficiencies were noted and the system was left operating normally.

Performed a descale service on the power-vented Rheem tank water heater, flushing mineral and sediment buildup from the tank and discharging the flush water to the adjacent floor drain. Following the service, the unit, venting, and electrical connections were inspected, and no leaks, corrosion, or visible damage were found.

Installed shutoff valves on the gas piping serving a multi-meter manifold in the basement utility area, connecting flexible gas lines with brass fittings and red-handled isolation valves to each meter. Verified secure connections and proper valve operation at each meter location, with piping routed overhead to the meter bank.

Performed a scheduled commercial heating maintenance visit, inspecting the return air ductwork and verifying the 16x25x1 filter installation, which was found to be dated 10/19/21 and in need of replacement. Measured duct surface temperature at 126.3°F with a digital pocket thermometer to confirm heating operation, and checked the foil-taped duct seams, with no damage, frost, or rust observed.

Performed seasonal fall heating maintenance on a natural gas furnace, including a combustion analysis using a Bacharach analyzer to verify safe and efficient operation. Flue gas readings were within acceptable parameters, with O2 at 10.5%, CO at 14 ppm, CO2 at 5.9%, and steady-state efficiency of 96.8%, confirming proper combustion and heat exchanger performance.

Performed seasonal heating maintenance on a 22-year-old basement-installed natural gas furnace. Completed a flue gas combustion analysis with a Testo 327-1, recording 9.2% O2, 69.7% excess air, 2 ppm CO, and 4 ppm air-free CO, all within safe operating limits and confirming proper combustion performance. The unit is operating normally, and the customer is due for maintenance plan renewal.