Heating & Air Conditioning Services in Hudson, OH

Completed fall maintenance inspection on natural gas heating system. Performed combustion analysis testing on both units, recording oxygen levels, carbon monoxide output, efficiency ratings, and carbon dioxide percentages to verify safe and optimal operation. First unit measured 5.2% O₂, 45 ppm CO, 97.4% efficiency, and 8.9% CO₂. Second unit measured 7.8% O₂, 10 ppm CO, 92.4% efficiency, and 7.4% CO₂. All readings documented and fall maintenance procedures completed per manufacturer specifications.

Responded to follow-up service call for furnace that failed to start during previous visit. Diagnosed and repaired faulty ignition control module and cleaned flame sensor connections. System tested successfully and verified proper heating operation before departure.

Completed fall maintenance on heating system. Performed combustion analysis using Bacharach Fyrite InTech analyzer, confirming optimal system performance with readings of 97.3% efficiency, 4.9% oxygen, 9.0% carbon dioxide, and 12 ppm carbon monoxide. All parameters within manufacturer specifications for safe and efficient operation.

Completed installation of Reznor heater unit with Quick Sling mounting system in new construction space. Shortened B-vent pipe protrusion from ceiling to proper specifications and secured all ductwork connections with metal clamps. Installed thermostat and associated electrical conduit, ensuring all ventilation components are properly mounted and functional.

Performed comprehensive tune-up on 3-year-old residential air conditioning system, including inspection of dual outdoor condenser units and interior ductwork. Conducted standard maintenance procedures, verified refrigerant lines, checked electrical connections, and inspected attic-mounted air handler and associated HVAC components. All systems tested and operating within normal parameters upon completion.

Completed full HVAC system retrofit including furnace and air conditioning equipment. Installed new outdoor condensing unit on existing concrete pad with proper refrigerant line connections and electrical conduit routed through exterior wall. Verified all connections secure and system operational. Equipment positioned against structure with adequate clearance for airflow and future service access.

Replaced toilet fill valve assembly after receiving the ordered replacement part. Upon arrival, installed the new fill valve mechanism and adjusted the float level to ensure proper water shutoff. Customer requested additional inspection of other plumbing concerns while on-site, which were evaluated and addressed as needed. Verified toilet operation, checked for leaks, and confirmed proper flush cycle and tank refill functionality before completing the service call.

Completed installation of CellarPro through-wall wine cooling unit in wooden alcove with integrated digital thermostat control. Unit was properly mounted in recessed wooden cabinet space, electrical connection established via standard wall outlet, and Copeland digital thermostat installed on adjacent wall surface displaying operational temperature reading of 63°F with system status indicators functioning correctly.

Performed leak test on HVAC unit #5 located in attic space. Inspected all refrigerant line connections, copper piping, and valve assemblies for potential leaks. All components, including furnace and air handler connections, tested and verified to be operating within normal parameters with no leaks detected.

Responded to service call for plumbing issues including constantly running toilet and shower stopper inspection, as well as refrigerator door concerns. Inspected toilet tank components and identified faulty fill valve requiring replacement; installed new Kohler fill valve assembly with waterline connection to resolve continuous running issue. Examined shower drain stopper mechanism and verified proper operation. Assessed refrigerator door alignment and seals, confirming functionality within normal parameters.

Completed rough-in installation for garage heating system, including placement and securing of heater unit and routing of gas supply line to unit location. All rough-in work positioned and secured per code requirements in preparation for final connections and system startup after wall finishing is complete.

Completed full HVAC system retrofit including outdoor air conditioning condenser unit and indoor vertical air handler installation. The outdoor condenser was positioned on a gravel pad against the building exterior with proper electrical conduit and refrigerant line routing through the siding, while the indoor air handler was installed in the basement mechanical room with integrated PVC condensate drainage system and pump. All components were properly connected, tested, and verified operational per manufacturer specifications.

Responded to reported leak near recently installed spigot in mechanical room area. Upon arrival, isolated water supply to affected zone and documented conditions with photos showing PVC piping system, HVAC ductwork, and exposed framing in adjacent construction area. Advised customer this may be callback-related to previous installation work and will assess whether leak originated from recent spigot installation or separate plumbing issue requiring additional repair.

Completed spring maintenance on commercial rooftop HVAC unit I-AX56. Performed comprehensive inspection of blower assembly, belt drive system, and refrigerant lines, documenting equipment condition with photographs. All components found operating within normal parameters with routine weathering consistent with outdoor installation.

Completed comprehensive HVAC system evaluation for air conditioning retrofit at residential property. Assessed existing outdoor condenser unit positioned against exterior brick wall, noting vegetation growth around equipment that required clearance consideration for proper airflow and maintenance access. Documented indoor basement mechanical room containing Bryant Plus 90i furnace and existing water heater with associated copper piping, PVC venting system, and ductwork infrastructure. Evaluated compatibility of current furnace system with proposed air conditioning retrofit, inspected electrical panel accessibility, and confirmed adequate space for refrigerant line routing between indoor and outdoor components. Provided detailed photographic documentation of both outdoor condenser location and indoor mechanical room configuration to support equipment replacement specifications and installation planning.

Conducted on-site assessment for complete HVAC system replacement involving existing Lennox furnace and air conditioning unit. Evaluated basement-installed furnace with current ductwork configuration and exterior condensing unit mounted on concrete pad. Documented existing equipment specifications, duct system layout, and installation conditions to provide comprehensive replacement quotation for new heating and cooling system.

Responded to service call for two malfunctioning anti-freeze spigots located in separate areas accessible through drop ceiling. Inspected both frost-free hose bibs mounted on exterior wall with gray PVC supply lines and copper piping infrastructure visible in ceiling cavity. Verified proper operation of shutoff valves with blue handles on copper supply lines. Repaired and tested both anti-freeze spigots to ensure proper drainage function and freeze protection capability. Confirmed all connections secure and leak-free at both locations.

Completed comprehensive maintenance service on geothermal HVAC system including air handler unit and associated equipment. Inspected and serviced all accessible components, verified proper operation of air filtration system, checked ductwork connections, and confirmed system functionality. All equipment found operating within normal parameters with no issues identified during inspection.

Completed warranty service on HVAC air cleaner system by replacing damaged or deteriorated wiring. Accessed the unit through existing service opening, removed old wiring, and installed new properly rated conductors to restore full functionality. All connections were secured according to manufacturer specifications and electrical code requirements.

Completed spring maintenance on a 5-year-old residential air conditioning system located in the backyard. Performed comprehensive inspection of the outdoor condensing unit, which showed signs of environmental exposure including organic growth and weathering on the exterior casing. Conducted standard preventive maintenance procedures including system evaluation, cleaning, and operational testing to ensure optimal cooling performance for the upcoming season.